PDU, 1 x 16 A, 8 x Safety Socket Typ F, 2 Sensor-Connectors, vertical Mounting, SSL, IPv6, SNMPv3, GUDE Expert Power Control 8314-1

8314-1: 8x safety socket type F             8314-2: 8x IEC C13

Key Features

• Event and schedule controlled switching
• Input current metering of up to 9 electrical units
• 2 connectors for plug-and-play sensors
• Simple and quick mounting due to integrated mounting straps
• NTP function can be activated

Switching function

• Each power port can be switched via HTTP(S), SNMP, ModbusTCP or command line interface via Telnet, SSH, MQTT and serial interface
• Programmable on/off sequences for remote reboots (Remote Reboot)
• Power ports can be switched when preset sensor thresholds are exceeded
• Self-healing function thanks to 8-channel watchdog: Each power port can be assigned its own Watchdog (ICMP/TCP), which initiates an automatic restart if necessary
• Switching state and switch-on delay up to 9999 seconds (166 minutes) individually adjustable for each output port after power failure
• Current peaks due to increased inrush currents are automatically prevented by sequential switch-on with a latency of 1 second

Metering function

• Power consumption metering (kwH) with 2 energy counters: one counter counts consistently, the other counter is resettable
• Metering of current (A), voltage (V), phase angle, power factor, frequency (Hz), active power (W), apparent power (VA) and reactive power (VAr)
• 2 connectors for combined plug-and-play sensors (temperature, humidity and air pressure) to prevent often occurring physical hazards like overheating and increased humidity or air pressure

Security

• Long-life High-Inrush Relays prevent welding of relay contacts during inrush current peaks
• Generation of status messages and alarms (e-mail, syslog, SNMP traps MQTT, SSH, Telnet)
• Encrypted e-mails (SSL, STARTTLS)
• Access protection by IP access control
• Encrypted communication through SSL (TLS 1.1, 1.2, 1.3) and SSH
• Password protected access
• Beeper for audible alarm when sensor limits are exceeded/deceeded

Operation

• Easy-to-read LED display for displaying total current, IP address and sensor values
• Firmware update via Ethernet during operation (no restart required)
• Simple and flexible configuration via web browser, Windows or Linux program
• Dynamic assignment of an IP address via DHCP or manual assignment of static IP address

Technical Details

• High-inrush relay: max. 4 sec: 30 A /max. 20 ms: 80 A
• Measurement of key electrical parameters: current (A), voltage (V), phase angle, power factor, frequency (Hz), active power (W), apparent power (VA) and reactive power (VAr)
• Encrypted communication through SSL (TLS 1.1, 1.2, 1.3) and SSH
• Vertical mounting, 0 HU
• LxWxH: 69 x 7 x 6 cm (length including pivotable mounting brackets)
• Weight: approx. 3.0 kg
• Length mains cable: 2.3 m
• Operating temperature: 0-50 °C
• Storage temperature: -20 – 70 °C
• Relative humidity: 0 – 95 % (non condensing)

Electrical Connections

• 1 power supply IEC C20 (max. 16 A, 230 V)
• 8 power ports safety socket type F (max. 16 A) for 8314-1
• 8 power ports IEC C13 (max. 10 A) for 8314-2
• 1 Ethernet connector RJ45 (10/100 Mbit/s)
• 1 serial interface RS232 (Sub-D, 9-pin)
• 2 connectors (RJ45) for plug-&-play sensors

Order code

• 8314-1: 8x safety socket type F
• 8314-2: 8x IEC C13

Scope of delivery

• Expert Power Control 8314-1 / 8314-2
• Quick start guide